Wilson In-Building Wireless iDEN 50 dB Amplifier (804005)

DO YOU HAVE SIGNAL PROBLEM?
We have a solution for you.

THIS AMPLIFIER IS ONLY FOR NEXTEL iDEN PHONES

Free Shipping in the U.S.A! The Wilson bi-directional cellular amplifier / repeater greatly improves signal strength inside a building when using your cell phone. It does this without physical connection to your phone allowing you to walk around freely during a call. It even allows multiple phones to be used simultaneously.

The signal is received by the outside antenna from the cell site. It is then amplified and repeated to your cell phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna, amplified, then repeated to the cell site via the outside antenna.

Installation Options:

Requirements (sold separately)

• Coaxial Cables
• Inside Antenna
• Phone adapters

	The Wilson 301103 Magnetic mount outside antenna is required, but one of the choices available for outside antennas.		The Wilson 301102 Glass mount outside antenna is required, but one of the choices available for outside antennas.
	The Wilson Dual Band Mirror Mount Trucker Antenna 301101 is required, but one of the choices available for outside antennas.		The Wilson Dual-Band Mini Magnet Antenna, 301113 is required, but one of the choices available for outside antennas.
	The Wilson 301124 Yagi Antenna is a required, but is one of the choices avilable for outside antennas.		The Wilson 301111 Yagi Antenna is a required, but is one of the available choices for outside antennas.

Antenna and Accessory Options

• Dual-Band Panel Antenna (301135)
• Low Profile Antenna (301106)
• Mini Magnet Antenna (301113)
• Trucker Mirror Mount Antenna (301101)
• 2-Way Splitter (859901)
• 20' Coax Cable (9913)
• 50' Coax Cable (9913)

Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) features

• For iDEN frequencies
• Increases signal strength in buildings for iDEN (Nextel, Southern LINC, Mike) frequencies (806-866MHz) (check compatibilites below)
• Power control logic ensures maximum output power is within cellular network standards
• Automatic shutdown on overload
• Oscillation detection and gain reduction with auto reset intervals
• AC power supply included
• FCC and IC type accepted
• Greater than 50dB computer controlled adjustable AGC dynamic range
• Automatic Gain Adjusting in the event of oscillation and/or overload
• 2dB Gain Steps (20 - 50dB)
• TIA/EIA-98-E 3.5.1 Receiver Sensitivity better than -110 dBm
• Wireless operation - no physical connection to cellular phone
• Maximum 3 Watts Output Power
• High Power Output Allows More Users on the System
• Allows multiple phones to be used simultaneously
• Increases your cellular phone's range
• Low cost solution for uncompromised performance
• Overload Protection on Uplink and Downlink
• Receive/Transmit Overload Indicator Lights
• Low Isolation Indicator
• Also works for direct connect communication

Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) specifications

• Part Number: 804005
• Frequency: 806-821 MHz / 851-866 MHz
• Gain: 50 dB
• Max Output Power: up to 3 watts
• Max RF: + 30 dBm / + 30 dBm
• Noise Figure: 3 dB nominal
• Flatness: ? 2.5 dB
• Isolation: > 90 dB
• Power Requirements: 120 V AC 3 A max
• Connectors: N-Female 50 ohms
• Dimensions: 5.6 x 3.6 x 1.7(inches) / 14.2 x 9.1 x 4.4 (cm)
• Weight: 1.5 lbs / 0.7 kg

For more information about Installation and Specifications, check out the Wilson Brochure below:

*A cell phone using our amplifier is safer and will use less battery power because the phone thinks it's much closer to a cell site than it actually is. Phones vary their power output based on their proximity to cell sites. Therefore, your phone transmits less power - resulting in safer use and longer battery life.

Note: Expedited shipping not available due to larger packaging requirements and weight.

Technical Support
Help may be obtained by contacting Wilson Electronics, Inc. at 1-866-294-4660 or tech@wilsonelectronics.com Monday through Friday between 7:00AM - 3:30PM Pacific Time.

FAQs - Click Here for more information on Antennas and Amplifiers.

Wilson In-Building Wireless iDEN 50 dB Amplifier (804005)

Order the Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) today! Don't miss out on this great deal with Free Shipping. The Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) is ready to be shipped within 24-48 hours.

Let the Geeks Experts help you with any questions or concerns. Call us today at 1-866-433-5793 or email us at CS@AccessoryGeeks.com.

Buy the Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) today at AccessoryGeeks.com